← 研踪 PaperTrailarXiv:2608.13233 · v3
Fabrication of Complex Soft Robotics: Challenges, Solutions, and Optimization
首次提交 2026-08-13 21:38
版本更新 2026-11-11 10:18
雷达观测 2026-11-13 11:11
摘要
Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications
观测到的版本
相邻记录可能跳过中间版本；首次发现 v2 及以上也会标为版本更新。
v3 · 2026-11-11 10:18 · 最新观测版本
Fabrication of Complex Soft Robotics: Challenges, Solutions, and Optimization
Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications
查看此版本解读 →查看此版本原文 ↗v2 · 2026-11-09 02:26
Manufacturing Complex Airtight Soft Pneumatic Actuators for Soft Robotics: Process Evaluation and Optimization
Manufacturing complex soft pneumatic actuators remains challenging because geometric fidelity, compliance, structural integrity, and airtightness must be achieved simultaneously. This study presents a manufacturing-focused evaluation of several fabrication routes for complex pneumatic structures, including heat-shrink forming, silicone casting, powder- and liquid-based additive manufacturing, and fused deposition modeling (FDM). The processes were assessed through process screening, baseline fabrication, failure analysis, and process improvement to distinguish inherent process limitations from correctable manufacturing defects. Heat-shrink forming was limited by geometric conformity, casting by mold accessibility and bonded interfaces, powder-based methods by residual material trapped within enclosed passages, and digital light processing by the material properties and post-processing requirements of the investigated system. FDM provided the most adaptable route because its dominant defects could be progressively reduced through process optimization. The results further showed that airtightness depends not only on nominal wall thickness but also on extrusion-path architecture, while support-free geometry is important when access for internal post-processing is limited. These findings establish a practical design-for-manufacturing approach in which process selection is guided by the compatibility between actuator architecture and manufacturing constraints. The proposed approach provides practical guidance for developing complex, flexible, and airtight soft pneumatic actuators for soft robotic applications
查看此版本解读 →查看此版本原文 ↗