跳到正文
研踪PaperTrail
← 研踪 PaperTrail

arXiv:2611.25921 · v1

A Lightweight Hybrid Approach for Milling Force Reconstruction from Internal Machine Signals

首次提交 2026-11-19 19:06
版本更新 2026-11-19 19:06
雷达观测 2026-11-20 19:57
arXiv ↗PDF ↗

摘要

Data-driven monitoring based on milling force can enable advanced manufacturing services including process optimization and condition monitoring. However, industrial implementation is often hindered by costly and intrusive hardware and large training data requirements. This paper therefore presents a hybrid approach using machine-internal signals and machining metadata to enable force-based monitoring on brownfield machines without additional sensors. Commonly available machine signals have relatively low sampling rates and cannot directly represent high-frequency milling-force variations, especially at higher spindle speeds. Instead of learning the complete force signal, which would increase model complexity, data requirements, and overfitting risk, a supervised machine-learning model predicts only the average milling force from selected machine-signal features and machining parameters. This low-frequency estimation parameterizes a static milling force model that reconstructs the force behavior over one spindle revolution. Although the static model does not reproduce all dynamic effects, it captures the force distribution, load levels, and angular regions of highest tool engagement. The approach is evaluated on one milling machine across varying process parameters, engagement conditions, cutting tools, and two workpiece materials. Dynamometer measurements are required only for development and validation. Ridge regression achieves an R2R^2 of 0.9840.984 and 0.9910.991 for average-force prediction on the test data (Fˉx\bar{F}_x and Fˉy\bar{F}_y). The reconstructed force behavior over one spindle revolution achieves an R2R^2 of 0.9620.962 and 0.9820.982 (FxF_x and FyF_y) compared with the reconstruction based on measured force features. The method provides a cost and computationally efficient basis for process monitoring, tool condition assessment, and process optimization on existing machines.

作者备注:Author-prepared preprint. 7 pages, 4 figures, 5 tables

AI 论文解读

基于摘要 · 非全文审阅

此版本尚未生成 AI 解读。解读由后台任务生成并按论文版本保存,登录后共享已有结果。

版本差异

目前只收录了一个版本。收录下一版后,可以对照标题、作者、分类和摘要。

观测到的版本

相邻记录可能跳过中间版本;首次发现 v2 及以上也会标为版本更新。

v1 · 2026-11-19 19:06 · 最新观测版本

A Lightweight Hybrid Approach for Milling Force Reconstruction from Internal Machine Signals

Data-driven monitoring based on milling force can enable advanced manufacturing services including process optimization and condition monitoring. However, industrial implementation is often hindered by costly and intrusive hardware and large training data requirements. This paper therefore presents a hybrid approach using machine-internal signals and machining metadata to enable force-based monitoring on brownfield machines without additional sensors. Commonly available machine signals have relatively low sampling rates and cannot directly represent high-frequency milling-force variations, especially at higher spindle speeds. Instead of learning the complete force signal, which would increase model complexity, data requirements, and overfitting risk, a supervised machine-learning model predicts only the average milling force from selected machine-signal features and machining parameters. This low-frequency estimation parameterizes a static milling force model that reconstructs the force behavior over one spindle revolution. Although the static model does not reproduce all dynamic effects, it captures the force distribution, load levels, and angular regions of highest tool engagement. The approach is evaluated on one milling machine across varying process parameters, engagement conditions, cutting tools, and two workpiece materials. Dynamometer measurements are required only for development and validation. Ridge regression achieves an R2R^2 of 0.9840.984 and 0.9910.991 for average-force prediction on the test data (Fˉx\bar{F}_x and Fˉy\bar{F}_y). The reconstructed force behavior over one spindle revolution achieves an R2R^2 of 0.9620.962 and 0.9820.982 (FxF_x and FyF_y) compared with the reconstruction based on measured force features. The method provides a cost and computationally efficient basis for process monitoring, tool condition assessment, and process optimization on existing machines.

查看此版本解读 →查看此版本原文 ↗