跳到正文
研踪PaperTrail

论文库

检索计算机领域论文,按研究方向、作者或关键词筛选。

部分采集异常
正在读取账号与研究记录…

全站更新概况

+479新增论文
+361其中 AI 相关
+64已有论文修订
+95新增 AI 导读

arXiv 最近完成扫描:2026-11-16 01:34 · 全站最近入库:2026-11-16 21:56各信源进度 →

统计口径与数据新鲜度

统计 2026-11-16 03:36 — 2026-11-17 03:36(北京时间) · 点击数字查看对应简报;AI 相关包含在新增论文内。

最近完成检查:2026-11-16 01:34最近发现新增版本:2026-11-16 21:56库内论文最新更新时间:2026-11-14 02:59

每分钟刷新已保存的数据。空检查不代表采集异常;新收录可能包含历史论文。AI 导读按新增版本计数。

23,827 已收录论文19,941 AI 相关6,922 有修订112 HF 社区发现

浏览论文库

时间范围跟随排序:版本更新、本站收录或首次发表。最新收录可能包含历史论文。部分信源异常,查看状态 →

找到 2 篇论文 · 按版本更新时间排序上轮扫描起点 2026-11-16 01:33(北京时间)
新论文 · v1arXiv:2610.36430

A Singularity Avoiding Track Model for Race Car Optimization

Adwait Verulkar, Behzad Danaei, Srikanth Sivaramakrishnan, Ryan Trinter

原文摘要

A track fitting pipeline is presented that converts a measured racetrack point cloud into a closed, $C^4$ differentiable, three-dimensional surface model suitable for high-fidelity Modelica race-car optimization. The surface is a Monge patch, parametrised by a curvilinear arc-length coordinate measured along the minimum-curvature line (MCL) and a signed lateral offset, with a height polynomial of user-selectable degree capturing the cross-sectional elevation profile. The choice of MCL as the reference line is deliberate since anchoring the same surface on the geometric centre-line can cause adjacent normals to cross inside the drivable region on tight corners. The resulting non-injective parametrisation assigns multiple curvilinear addresses to the same three-dimensional point and returns invalid road geometry. The MCL is obtained from a quadratic program that minimises integrated curvature subject to track-boundary, periodicity, and jerk-regularisation constraints. By reducing total curvature while remaining within the track bounds, the MCL moves the region of parametrisation breakdown outside the drivable strip on all circuits studied, keeps the normal map injective across the full track width, and yields a more linear time-to-arc-length transformation for minimum lap-time problems. The fitted surface and the associated track widths are exported as periodic piecewise-quintic $C^4$ B-splines, solved as a nonlinear program.

cs.RO · eess.SY

新论文 · v1arXiv:2610.36407

A 2-DOF MultiBody Track Joint for Race Car Optimization

Srikanth Sivaramakrishnan, Behzad Danaei, Adwait Verulkar, Ryan Trinter

原文摘要

TrackJoint is a Modelica MultiBody component that turns a three-dimensional road surface into a joint with two degrees of freedom. The two joint coordinates are the distance travelled along a reference line and the sideways offset from that line. Together they give the position, orientation and angular velocity of a single frame_b connector. All road geometry reaches the joint as a small set of periodic piecewise-quintic splines, so one component can represent any circuit whose splines have been fitted beforehand. The road constraint is closed with d'Alembert's principle. The two generalized forces that belong to the joint coordinates are set to zero, so no Lagrange multipliers are needed. The joint is connected to a multibody race car in Dymola and the pair is exported as one FMI~3.0 FMU. The same FMU is then used for time-domain simulation and for CasADi/IPOPT minimum lap-time optimization, with no change to the model in between. This works because the joint keeps the arc-length coordinate as a real state and publishes its time derivative, which is the quantity that lets the problem be rewritten with distance We report results for minimum lap time simulations on the Singapore Formula~1 circuit.

cs.RO · eess.SY